惠华电子-国内领先的双面液晶屏,透明液晶屏研发生产制造商
 专注于-长条|拼接|双面|展柜|冰箱|售货机解决方案

TEL : 15171212116
产品详情
惠华22”透明液晶屏
产品尺寸: 22inch
分辨率: 1680*1050
可视角度: 80/80/80/80 (Typ.)(CR≥10)
产品详情

HH220-TMP01 is aactive matrix liquid crystal display (LCD) that uses amorphous silicon TFT(ThinFilm Transistor) as switching components. This model is composed of a TFT-LCDpanel, a driver circuit. The resolution of a 22.0“ is 1680 x 1050 and thismodel can display up to 16.7M colors with wide viewing angle of 80 or higher inall directions. This panel is intended to support applications to provide aexcellent performance for Flat Panel Display such as Transparent DisplayMonitor, Show window, Kiosk etc.

     Product Highlights                                                       KeyMarkets

ROHS compliance (PB-free)  High Transmittance  TN(Twisted Nematic) mode                                Exhibitioncabinet

Wide viewing angle Highspeed response WXGA(1680 x 1050 pixels) resolution (16:10)                  Digitalsignage innovation products

Low power consumption DE(Data Enable) mode  Interface – TMDS(Main),LVDS(Option)

Connecter – HDMI

   Specificationsfor HH220-TMP01

 Do not leave the Module in high temperature, and highhumidity for a long time. It is highly recommended to store the Module withtemperature from 0 to 35 and relative humidity of less than 70%. Do notstore the TFT-LCD Module in direct sunlight. The Module should be stored in adark place. It is prohibited to apply sunlight or fluorescent light in storing.Do not connect or disconnect the Module in the "Power On" condition. Powersupply should always be turned on/off by the "Power on/off sequence"Module has high frequency circuits. Sufficient suppression to theelectromagnetic interference should be done by system manufacturers. Groundingand shielding methods may be important to minimize the interference.  Do not use liquid cleaner at LCD surface  .Use cover glass at LCD.Whenthe module is assembled, It should be attached to the system firmly using everymounting holes. Be careful not to twist and bend the modules. Refrain fromstrong mechanical shock and / or any force to the module. In addition todamage, this may cause improper operation or damage to the module andback-light. Note that polarizer  are veryfragile and could be easily damaged. Do not press or scratch the surface harderthan a HB pencil lead. Wipe off water droplets or oil immediately. If you leavethe droplets for a long time, Staining and discoloration may occur. If thesurface of the polarizer is dirty, clean it using some absorbent cotton or softcloth. The desirable cleaners are water, IPA(Isopropyl Alcohol) or Hexane. Donot use  Ketonetype  materials(ex. Acetone), Ethyl alcohol,Toluene, Ethyl acid or Methyl chloride. It might permanent damage to thepolarizer due to chemical reaction. If the liquid crystal material leaks fromthe panel, it should be kept away from the eyes or mouth In case of contactwith hands, legs or clothes, it must be washed away thoroughly with soap. Protectthe module from static , it may cause damage to the CMOS Gate Array IC. Usefinger-stalls with soft gloves in order to keep display clean during theincoming inspection and assembly process. Do not disassemble the module. Do notadjust the variable resistor which is located on the module. Protection filmfor polarizer on the module shall be slowly peeled off just before use so thatthe electrostatic charge can be minimized



会员登录
登录
我的资料
留言
回到顶部